Quick Pool Installation

IMPORTANT: When Using Blocks or bricks to support your soft sided pool you must use the bricks or patio blocks UNDER ALL OF the pool legs or the unsupported legs will sink deeper causing an imbalance of the pool and a worsening of level and stress on the pool. 

Also The ground under the pool must be firm, or it will compress and fall away leaving the pool pulling on the supports, which will cause the seams to fail. Adding one inch of clean soil under the pool bottom might be helpful. The pool bottom MUST touch the ground 100% if the pool bottom is stretched tearing and seam breakage can occur. 

Also do not leave pool ladder against the Pipe or the Pipe will break.

Should for any of these reasons or other reason, your liner fail we have products to easily repair seams and cuts or tears.

Vyna Bond Fast Acting Super Strength Contact adhesive for seams cuts or tears (very rare)

If you do not have the material to repair the leak. we offer Flexible Sealer From  Leakmaster, it creates patches or material from a tube.

In case of small tears in seams the warranty does not call for a replacement liner. Materials for repairing small tears are listed above and can be obtained from us.

Click Here For Information From the Manufacturer Regarding Pinhole Leaks

Step 1 - Take the liner bag and ground sheet out of the box; place the liner at the center of the ground sheet  where you plan to place the pool. Be careful not to damage the liner when using a knife to open the box. Clear the area of any sharp objects.

Step 2 - Unfold the liner. First note which side of the pump is to be connected to the liner where the thru-the- wall fittings will be connected.

Step 3 - Spread the bottom sleeves flat on each side of the liner. *Number of bottom sleeves will vary for each side depending on the pool size. It is also advised that the thru-wall fittings be put on the liner at this stage; it is easier putting them on now rather than after the pool is standing up.

Step 4 - Put one U-pipe through each of the bottom sleeves so the open ends of the U-pipes will be pointed outwards.

 Step 5 - After finishing Step 4, use longer side of the liner in order to connect pipes easily one after the other. To make it easier, prepare all straight pipes connected and ready, then connect comer pipes (if applicable to the type of pool you have) at the end. *Make sure the pipes are well connected and consistent. Also, there are four different shapes of pipes that have square pinholes on the surface. These pipes should be connected to the comer pipes that have pins on the surface.

Step 6 - Connect stand-pipes to the frame that you've already made above through the liner holes. Those two  pipes have male and female ends so you have to twist the stand-pipes in order to hold them tight and fixed.

Step 7 - Lift up stand-pipes and connect them to U-pipes at the same time.

 Step 8 - After finishing step 7, you will get an approximate shape of the pool. However, make sure that all connected parts are fixed and well connected. It will be hard to adjust after filling with water because of the water pressure.

 Step 9 - After installing skimmer, pump and filter, fill the pool with water. Now, you are ready to swim!!  NOTE: When you fill the pool with water, pull the sleeves outward in order to get the perfect shape of the pool. (The level of inner water should be about 7" from the top of V2way up the skimmer to achieve the skimming effect of the filter system. This level of water will skim off bugs, spiders, gnats, etc. You can also determine prevailing wind direction and locate the skimmer downwind. The wind will blow debris into the skimmer. Use thru-wall fittings to connect pump to the liner of the pool. Leave one eyeball connection in thru-wall fitting to set water direction. Some pools have 2 holes - return and suction. Others have a third hole at the bottom, which is a drain.

Step 10 - If using Happy Bottom, duct tape the strips together, place liner on pad and trim off excess. Use onyx black pebble or white rock to decorate your pool from liner out to edge of pool. Also potted flowers, which are available at many discount stores, will make your pool more fashionable.

 Step 11 - On occasions when you're having a pool party, use Filter Aid ($5.99) and Water Clarifier ($7.99) to completely remove all contaminants from the water. "Should be able to read date on a dime from 4 feet." You can order these items online.

 Step 12 - The replacement cartridge for your filter is identified by the circled number on the top right hand corner of the blue and gray label on the filter tank. Simply give us this number to order online. The price reflected on our website is 40% off pool store prices.